What can you cook from squid: quick and tasty

Situations are widespread when it is not installed simultaneously with the plastic window, but after a certain period of time. The difficulty lies in the fact that a standard mosquito net may not fit the dimensions of the window, in which case you need to know how to measure a mosquito net, which will be made to order, in accordance with the dimensions of the customer's plastic window.

Why is it important to correctly measure a plastic window for a mosquito net

Incorrect measurement can lead to negative consequences, for example, if the mesh is too large for the window, then it will be difficult to install, and if it is too small, there will be cracks through which insects and foreign objects from the street will enter the house.

How to correctly measure mosquito nets?

To take measurements, you will need a regular tape measure and a notebook with a pen to write down the results obtained (with millimeter precision).

The main stages of measurements:

• Measurements are taken on an open window, therefore, it is necessary to open the sash on which the mesh will be attached;
• Then the width and height of the skylight are measured (along the edge where the sealing elastic is located);
• At the end, measurements are made of the external dimensions of the frame in order to make sure that the particular type of mesh on the selected window is suitable for installation.

Types of fastening mosquito nets: features of their measurements

The design of mosquito nets is usually the same and consists of an aluminum frame and fiberglass cloth. In order for the mesh to fit snugly against the window, due attention should be paid to the quality of the fastening. Mosquito nets have different types fasteners, so first you need to decide which type you decided to install:

Mount types:

• Z-shaped mounts. They are especially popular because they provide high reliability of fastening. Fastening takes place using nickel-plated brackets that fit snugly to the frame;
• Plunger (rod) mountings. This is a universal mount, suitable for all types of windows. The plunger is a metal pin with a spring (adjustable in length) to which the mesh frame is attached;
• Fastening "pockets". Less common as it does not provide adequate protection.

How to calculate the size of a mosquito net from measurements

In order to calculate the dimensions of the future mosquito net with a z-shaped fastening for plastic windows (see), it is necessary to add 20-25 mm to the obtained height and width of the opening. In addition, it is important to understand whether it is possible to install a mesh with such an attachment. For this, the depth of the window frame structure is taken into account, it can be tightly wound up by a quarter, therefore, difficulties will arise during installation. In this case, it would be more expedient to put a mesh with plunger mounts, but it is unsuitable in several cases: if the frame bevel has a round shape and a large angle of inclination.

This is due to the fact that during installation, the pins are attached to the frame profile, and given the large bevel, it will not be possible to achieve the proper strength and reliability. To calculate the size of the mesh from the results obtained, the height and width of the opening are subtracted by 5-6 mm (under the space for the sealing brush, which is mounted along the perimeter of the frame during installation). In order to calculate the size of the mesh with "pockets" fastening, it is recommended to consult an experienced specialist.

In my renovation, I got my hands on the windows. I have building renovation and therefore plastic windows were! (which is already pleasing), but there was no finishing - no slopes, no mosquito nets, and the windows themselves were not adjusted (they do not open well - they close). The slopes were made (not without help), I will try to write an article later, but the question arose about installing mosquito nets. But first you need to measure them ...

If you call a measurer + installation of mosquito nets, then it will cost twice as much as measuring and installing the mosquito net yourself. I will definitely write about the installation of the grids, but now you need to correctly measure the grid so that it completely covers the window. Measurement must be accurate, otherwise the mesh must be altered.

So, how the mosquito net is measured.

Everything is very simple, in order to make a mesh, you need to take off the dimensions of the inner sash, on which we will hang the net from the outside. That is, the sash that opens, as a rule, is half of the window. We measure its width and height, just like in the photo.

Then we transfer these dimensions to production, usually the nets are made by manufacturers of plastic windows, they are made in 15 minutes, they can be made with you. average price we have about 600 rubles per square meter in our city.

The dimensions of the sash are 1.47 meters by 0.6 meters = 0.88 square meters. Then we multiply by 600 rubles, it turns out 600 * 0.88 = 528 rubles

We also need to buy fasteners for the mesh on the window, they cost a penny, about 10 rubles for a fastener. You need 4 fasteners per window = 40 rubles.

That's it, it's so easy and simple to measure the mosquito net.

Watch the video version of the article.

Read the next part, read our construction site.

How to measure a plastic window for installing a mosquito net

It is not uncommon for a mosquito net to be ordered some time after the windows have been installed. In fact, if new double-glazed windows were delivered in the fall, it might well be possible to postpone the cost of a mosquito. But, when the owners nevertheless decide to order this necessary window accessory, they are faced with a problem. Manufacturing companies do not make standard meshes. Each of them is made to order, strictly according to the size of the window.

In such a situation, there is three options .

• Order a mosquito in the same company that did your windows. It is possible that your order with size data remained in their archive.
• Call the measurer at home. This means a waste of time and expense to pay for the departure of the master.
• Measure the window for the mosquito net yourself.

The third option seems to be the most convenient. But before making measurements, you need to know a few subtleties.

As a rule, frame mosquito nets are installed on plastic windows. They are fairly inexpensive and easy to manufacture. Their design is simple - a fiberglass mesh with a 1 mm mesh is attached to an aluminum frame with a section of 10 * 25mm. But these accessories differ in the installation method. Depending on the manufacturing company, you may be offered different kinds mosquito:

Before measuring the light opening, decide what type of mosquito you are going to order.

The most effective and durable is the plunger mount. The mesh frame is attached to the window with nickel-plated spring pins. They provide a snug fit to the structure and aesthetics outside and inside the premises.

Z-shaped mounts- the second most frequently used option. Here, the mosquito structure is attached to the window frame using special metal brackets adjacent to the window seal. This mount is strong enough. But after a couple of years of use, the staples may loosen and gaps appear between the mesh frame and the window.

The third type of fasteners - "pockets"- it is used quite rarely, since it cannot provide a sufficiently snug fit of the mosquito protection. The mesh for this method is made with a margin in the width and height of the window opening. Here, for accurate measurements, it is still better to contact a specialist. In the other two cases, you are quite capable of calculating the dimensions of this product yourself.

To determine the size of the future mosquito net, you will need a tape measure. Open the window and measure the width and height of the skylight. Measurements must be made along the edge of the sealing gum, which is supplied with all plastic windows. Record your results exactly, down to the millimeter.

Product dimensions are calculated as follows:

To understand whether there is enough space around the frame for mounting a mosquito, it is also necessary to take into account the installation depth of the window frame. If from the side of the sash it is wound too tightly under a quarter, difficulties may arise when installing the mesh. Installation will be difficult even if the slopes of the plastic window are made too close to the frame edge. Consider these factors when deciding your mesh type. If the frame design does not allow z-mounts to be installed, you can order a ram mesh.

Installation of a mosquito net on the pins is possible if the bevel of the outer protrusion of your window frame does not have a round shape and too large an angle of inclination. Since the spring pins are attached to the very profile of the window frame, with a strong bevel, they will not be able to ensure sufficient tightness of the parts.

To calculate the dimensions of the future mesh, measure the height and width of the skylight, as in the previous case. Further, subtract 6 mm from the obtained dimensions. This is to leave room for the sealing brush, which is mounted around the perimeter of the mesh frame during installation. The received data can be reported to the office where you are going to place an order for a mosquito.

It makes sense to order frame nets for plastic windows only if the window sashes open to the inside of the apartment... Other types of insect repellent are available for other window designs.

When taking measurements, take into account each millimeter division of the tape measure. For z-mount accessories it is permissible to round the data, but only upwards. If the mosquito structure after installation will give a slight overlap on the frame from the outside - it's okay. The main thing is that it completely covers the light opening, preventing access to insects, small debris and poplar fluff.

As you can see, you can measure the plastic window for installing the mosquito net yourself. If, after reading the article, you still do not understand any points, you can refer to one of the video instructions for taking measurements.

Petrenko Andrey Yurievich

Order mosquito nets with a full range of services (measurement, manufacturing and installation) is the most correct solution, since the probability of an error is minimized, but even if it did happen, then the entire responsibility falls on the shoulders of the selling company.

When buying only the product, you independently remove all dimensions and install the mosquito net, in which case the responsibility for possible errors in measurement or installation falls on your budget. The cost of an anti-mosquito with this option is significantly reduced (on average, by 350-400 rubles per square meter). With volumes of 1-5 sq. M, this price difference will not be so significant, with larger orders (from 10 sq. M.), Savings of 3500 - 4000 rubles. and more will make a significant contribution to the family budget or save a decent amount for the company. But how to properly measure the size of mosquito nets?

Our company offers two options for fastening m / s - external z-shaped and internal metal. In this article, we will try to explain in detail and in an accessible way what nuances you should pay attention to when taking measurements, in which cases one or another type of fastener is used, and also how to correctly calculate the size of a mosquito net, because formalizing ordering mosquito nets, you must inform THE EXACT SIZE OF THE MOSQUE NET AND TYPE OF MOUNTING .

Option 1: internal metal fasteners.

Their main advantage is their versatility. Regardless of how your PVC window is installed, you can almost always install a mosquito net with this type of fastener on it.

Before proceeding with the calculation of the dimensions m / s, we need to make sure that its installation will be possible. To do this, it is necessary that the distance from the outer slope to the edge of the frame overlap on the right and left (A and C in the first figure) is greater than or equal to 10 mm, and above or greater than 20 mm (D in the second figure). If so, then you can safely proceed to measurements. First of all, we measure the light opening (the distance from the overlap to the overlap in the width and height of the letters B and E, respectively), then add 20 mm to these dimensions and get the finished size of the mosquito net.

For example, take window block size 1450X1450 mm divided in half. Depending on the profile system, the size of the skylight will vary. In our case (Brugmann profile system), the size of the light opening of one window sash is 620X1315 mm. We add 20 mm to each parameter and we get the finished size of the mosquito net equal to 640X1335 mm. Thus, making out ordering mosquito nets in our company without installation, you will have to name the width and height of the mesh you need (in this order) and the type of fastening. Based on our example, it will look like this: Good afternoon. I would like to place an order for a frame mosquito net with metal internal fasteners in the size 640x1335 mm, without measurements and installation.

Option 2: external Z-shaped mounts.

External fastenings are considered the most preferable, since the frame mosquito net is located on the outside of the window, and, therefore, the light opening does not decrease and the tightness of the primary seal circuit is not compromised. The only drawback may be considered some restrictions on their use. The ideal option is considered when the distance from the outer slope to the overlap on the right and left should be at least 20 mm, and from the upper slope to the overlap at least 50 mm. Only at such distances will the mosquito net not occupy part of the light opening. If your window is still recessed into the opening and these parameters are less, and there is no desire to put metal fasteners (due to a violation of the tightness of the window), then you can install external fasteners, but
the light opening will decrease by a certain amount. In this case, the minimum distances will be considered: 10 mm to the right and left, 30 mm from above, if the distances are even smaller, then only a specialist can determine the possibility of installation.

Now directly about the measurements. Initially, we measure the light opening, then, guided by the rules below, we calculate the dimensions of the mosquito net.

A. the distance to the right and left is 25 mm, we add 36 mm to the width of the light opening;

B. the distance to the right and left is 20 mm, but 25 mm, we add 31 mm to the width of the light opening;

B. the distance to the right and left is 15 mm, but 20 mm; add 26 mm to the width of the light opening;

D. the distance to the right and left is 10 mm, but 15 mm, add 21 mm to the width of the light opening.

2. Height of the mosquito net:

A. if the distance is 50 mm, then add 50 mm to the height of the light opening;

B. if the distance is 40 mm, but 50 mm, then add 45 mm to the height of the light opening;

B. if the distance is 30 mm, but 40 mm, then we add 35 mm to the height of the light opening.

An example of calculating the size of a mosquito net.

The light opening is 620X1335 mm, on the left is an impost (part of the window is 60 mm), to the right of the slope to the overlap of 17 mm, on top - 37 mm.

Since when calculating the size of the mosquito net, the smallest of the available distances from the slope to the overlap is taken, in our case it will be 17 mm. Based on the first rule, 26 mm must be added to the width of the skylight. According to the second rule, 35 mm must be added to the height. Thus, the size of the mosquito net for installation on external mountings is 646X1370 mm, while the opening will decrease by approximately 15 mm on each side.

We examined the main nuances of measuring m / s, guided by our rules, you can independently calculate the size of the product you need, order it from our company and install it, while saving up to 400 rubles per sq.m. If you doubt that you have correctly calculated the dimensions or that you can install external fasteners (because for this you need to lean out of the window), then you can always contact our company and order a mosquito net with measurements and installation by the company's masters. In this case, you are insured against any mistake, because all responsibility rests with our specialists, you can safely continue to do your household chores, and we will do what we have been doing for five years - the manufacture and installation of mosquito nets.

This instruction is for guidance only and applies only to mosquito nets produced by our company. In the case of ordering a mosquito net from the Zolotoy Klyuchik company without measurements and installation, all responsibility for incorrectly taken measurements, errors during installation or mismatch in dimensions due to errors in measurements lies with the customer.

The recommendations described in this article apply exclusively to profile systems with smooth rectangular or slightly rounded beads (Aluplast, Brugmann, Rehau, Gealan, KBE, Viva, etc.). For PVC profiles with a sharp bevel of the overlap (Deceuninck, Thyssen, Foris, Roplasto, etc.), this instruction is not suitable. In this case, it is necessary to resort to the services of the company's specialists. If necessary replacement of mosquito nets existing mosquitoes, the final size will be the size of the existing mosquitoes.

How to correctly measure and install a mosquito net?

Affordable and maximized effective way to protect your home from annoying insects are mosquito nets. Installing a mosquito net avoids the use of fumigators and other chemicals to combat annoying insects.

The mosquito net also prevents dirt and dust from entering the room, as well as poplar fluff (which is a powerful allergen). The mosquito net will keep pets from falling out of open window... The mosquito net is an aluminum frame on which a fiberglass mesh is stretched.

Types of mosquito nets

Frame mosquito nets- the classic design of the mosquito net. A strong mesh is fixed on the aluminum profile, such a structure is inserted into window hole... Such nets are convenient and practical, they are usually used when there is no need to constantly open the mesh. Depending on the method of fastening, they can be stationary and opening. Frame mosquito nets are recommended to be removed on winter period for the longest possible product life. If a large mosquito net is needed, it is usually made with an additional reinforcing bar in the middle.

Door mosquito nets practically do not differ from frame meshes, the design is also a lightweight aluminum profile. The main difference between frame and door mosquito nets is the size of the used aluminum profile. The door mosquito nets are larger. Handles are installed on the door mosquito nets for ease of use. Such nets are universal; they can be installed on entrance or attic doors, or on doors of balconies and loggias.

Rolling mosquito nets they work on the principle of roller shutters, that is, if necessary, the mosquito net can be rolled up into an aluminum box. The design of such a mosquito net includes a guide profile, a net in a roll and a cross bar with handles. Such mosquito nets are as functional and convenient as possible. There is no need to completely remove the roller mosquito net for the winter, just twist it up. Another advantage of such nets is the ability to cover wider window openings. But, as a drawback # 8212; such meshes are unfortunately short-lived.

Mosquito net with Velcro or Scotch tape- the simplest mosquito net, which is mounted on the inner side of the sash. If necessary, such a mesh can be removed very easily and quickly.

We measure the window under the mosquito net

Framed mosquito net with swivel z-mounts is the most popular option among customers. So, in order to independently measure the mosquito net, you need to take a tape measure, paper and a pen. Open the sash where the mosquito net will be installed. Now we measure the light clearance of the frame in width and height.

Mosquito net width on swivel z-mounts will be equal to the frame width plus 20 mm.

Mosquito net height on swivel z-mounts will be equal to the frame height plus 20 mm.

Types of mosquito net fastening

Plunger mount for mosquito net- the most expensive fastening of a mosquito net, but also the most reliable and stable fastening to high wind loads. The plunger is a special metal piece with a spring that can be adjusted in length. The plunger mount is universal for all types of windows.

Fastening "flag"# 8212; fastening the mosquito net with small plastic hooks. Such a mount is less resistant to wind loads.

Fastening with swivel z-elements- the most popular and reliable mount. The z-shaped elements must fit snugly to the frame, and are additionally fixed to it from the inside of the room.

Fastening to plastic corners. Such corners are located on the outside. This design does not interfere with the normal opening and closing of the window, and can also be easily removed.

Installing a mosquito net

Installing a mosquito net on swivel z-mounts runs in this sequence.

1. We place the mosquito net with fastenings inside the room. The bindings differ in the length of the hook. It is important that the fasteners are located with a smaller hook to the bottom, and a larger one to the top, respectively.

2. It is necessary to grip the net by the side vertical handles. Which can be metal or plastic. We install the mesh in the window opening and start large hooks on the upper part of the frame. In this case, the mesh must be raised to the maximum height. When you reach the maximum positioning height, you will be able to make smaller hooks on the bottom edge of the window frame. Ready.

Fastening the mosquito net with plastic corners differs in that the fasteners are installed on the window frame, and not on the mesh as in the previous version.

1. It is necessary to make markings for the plastic corners on the outside of the window frame.

2. We fix the plastic corners on the window frame with self-tapping screws.

3. Further installation is similar to the method of fastening with z-shaped elements (first the upper edge, then the lower).

When ordering from two mosquito nets in our company, we leave and take measurements completely free of charge (when ordering nets with installation).

If you need to order meshes without installation or place an order for only one mesh, then we will help you measure yourself with this material.

To remove correct sizes nets, it is necessary to open the sash of the window and measure the light opening in the frame in width and height (opening from the seal to the seal).

In this case, it is better to stick to the lower or upper part of the skylight, since the middle can have a "run-up" of up to 10mm if the frame is not correctly installed, which can significantly affect the result and the nets may not fit.

40 mm are added to the light opening to the width and height of the light opening, since the aluminum frame from which the mesh frame is made has a width of 20 mm and it covers all possible bends of the profile.

In addition, it is worth paying attention to how much the frame is deepened into the wall of the house from the street, and whether there is the necessary 20mm on each side. If the frame is strongly recessed into the wall and protrudes by less than 20mm, then you can add not 40mm to the light opening, but 30-35mm.

When measuring mosquito doors or measuring mosquitoes on single-leaf windows, you must also measure the width from wall to wall along the street side, and make sure that the mesh size after adding to the light opening is no larger than the opening between the walls. Otherwise, the mesh may not fit into the opening.

These rules for measuring mosquito nets on already installed windows are valid for both plastic and aluminum frames. By following the measurements above, you will be able to take the correct measurements and your mosquito nets will fit perfectly to the windows.

In order not to worry about the size of your grids, you can call our measurer and installer, who will accurately measure the dimensions and yours will perfectly fit the windows.

A mosquito net is an item that is not always installed on windows right away. Sometimes you have to purchase it separately or you need to replace the damaged one. That is why it is important to know how to measure the mosquito net on the window and choose the product you need according to the parameters. Different grids differ in design, and they need to be measured in different ways.

Determining the mesh size

If not already, measuring how it should be is the hardest part. To do this, you need to know how to take measurements for a mosquito net, depending on what type of it you will have. Hiring a specialist is not necessary: ​​you only need to stock up on a tape measure and devote a few minutes to the process.

Dimensions may vary depending on the type of mounts installed. The product is usually placed from the street side, attached to the frame using special metal hooks. Please note that the mesh should completely overlap the window opening, slightly going beyond the frame.

Measurement of mesh sizes

In order to understand what size should be , you will need to measure the height and width of the window opening. In this case, you need to add the following numbers to each parameter:

How to measure a stock-type mosquito net?

This product model is available only for those windows that are equipped with. The mesh is inserted into the recesses that are in the opening when the sash is open. The size of the mosquito nets must fit the window well.

Types of fasteners and sizes for them

The frame should not have a strong or rounded bevel, otherwise it will not work to install such a mesh.

Before you take the size for the window , make sure it is suitable for this type of mosquito nets. Measurements are simple: you need to measure the width of the window opening, starting from the outer protrusions of the frame. After that, 1 cm is subtracted from each parameter.

During installation, the mesh must leave a technical gap: it is approximately 5 mm. A sealing brush is inserted into the gap, which prevents debris and insects from penetrating into the gap.

Cases preventing the installation of a grid

There are options when the mesh cannot be fixed to the window:

• This problem can be caused by a metal grill located close to the frame. You can get out of the position only with the rod mesh. The roll model will not work due to the large thickness of the box. If the grille is close, the Z-bracing may not always be available.
• The same problem is caused by the closing of the frame with a concrete quarter: only the rod mesh will be applicable.
• An almost stalemate if one of the above factors is present, and the frame has a large bevel. In this case, you will not be able to use a mosquito net at all.

Knowing how to correctly measure the window for , you can choose a convenient option for yourself and get rid of insects in the house. You do not need to invite a master for measurements.