What can be cooked from squid: quick and tasty

Compact ventilation system In heating systems, many of modern houses used by solid fuel... In most cases, such systems are unprofessional designed and do not anticipate the flow of fresh air into the room.

Despite popular belief, periodic opening of doors and windows is not an effective solution to the problem. When there is insufficient fresh air in the room, the result is a lack of oxygen and incomplete combustion, and carbon monoxide CO, a highly toxic, odorless and colorless gas, is produced in the room. CO is a threat to our lives and health and is the cause of accidents when heating with solid fuels.

To ensure a healthy microclimate when heating with a fireplace or solid fuel stove, fresh air must be supplied to the room, at least 4 cubic meters / h for each kilowatt of thermal power (when heating with a fireplace with an open flame, the need for fresh air is much greater ). Considering the need for overpressure in a room with a fireplace or solid fuel stove, the use of a ventilation system that provides an inflow clean air, especially important for both good burning and for our health.

MMotors offers a solution to this problem using a series COMPACT VENTILATION SYSTEMS - "ECO-FRESH".

The compact ventilation system "ECO-FRESH" creates a healthy microclimate by delivering clean, filtered air saturated with oxygen and negatively charged ions into the room. The system cleans the air entering the room from odors, dust, bacteria and car exhaust gases. The device has a built-in hydrostat, which successfully controls the humidity in the room, keeping it below 75%, which limits the humidification process and prevents the formation of mold and mildew. The negatively charged ions released during operation of the device act antiseptically, suppressing the growth of pathogens - viruses and bacteria, thus protecting against infections and acute respiratory diseases. Ionized air increases efficiency, eliminates fatigue, provides positive influence on well-being, helps to recover after long and severe illnesses and has a beneficial effect on bronchial asthma, respiratory diseases, migraines, neuroses and diseases of the cardiovascular system.

Advantages Eco-Freshness 01

• Provides fresh air and a healthy indoor climate;
• Cleans and ionizes incoming air;
• Removes stale air from the room;
• Creates overpressure, assisting complete combustion and removal of flue gases;
• Controls humidity and prevents the spread of mold and mildew in the room;
• Using the "Recuperation" mode leads to a significant reduction in heat loss.

Installation characteristics:

1. Removes exhaust air from the room and replaces it with fresh outdoor air.
2. It controls the excess of the permissible level of carbon monoxide, ensures the most complete combustion of the fuel, and increases the removal of flue gases. (only for Comfort version)
3. Cleans the incoming air from dust, harmful impurities, bacteria and unpleasant odors.
4. Controls and regulates the level of humidity in the room, prevents the formation of mold and mildew.
5. Reduces heat loss in winter and saves energy consumption of cooling units in summer by using a highly efficient ceramic heater.
6. With the help of a built-in ionizer, it saturates the air with negatively charged ions. Ionized air increases efficiency, eliminates fatigue, has a positive effect on well-being, helps to maintain health, has a beneficial effect on bronchial asthma, respiratory tract diseases, migraines, neuroses and diseases of the cardiovascular system.

Specifications

The compact dimensions of the unit allow it to be mounted inside a room wall.

Eco-Freshness ventilator complete set

The Eco-Freshness 01 air handling unit includes:

1.External protective grill - protects the system from moisture, even in heavy rain.

2. Telescopic air duct - allows you to adjust the length of the device in accordance with the thickness of the wall.

3. The suction fan - two-speed, allowing to regulate the flow rate from 45 m3 / h in the night, silent mode of operation, up to 70 m3 / h in the day mode.

4. Filter:

Activated carbon filter - guarantees fresh air flow even in heavily polluted urban and industrial areas. Cleans the air from odors, dust, bacteria, soot, exhaust gases from cars, etc.

Fine filter - used in heavily polluted regions.

5. Recuperator (heat exchanger) - contributes to a significant reduction in temperature losses during ventilation of premises.

6. Ionizer - saturates the air with negative ions. Removes specific and unpleasant odors. Destroys pathogens. Prevents mold and mildew treatment.

7. Blower fan - two-speed, allowing to regulate the flow rate from 45 m3 / h in the night, silent mode of operation, up to 70 m3 / h in the day mode.

9. Humidity sensor - turns on ventilation when humidity exceeds 75%.

10. Carbon monoxide (CO) sensor - turns on the supply fan in the Air Flow mode -> 70 m3 / h, when the CO level is higher than the allowable one. (only for Comfort version)

Instrument control

The control is carried out by means of the remote control. The following operating modes are provided:

The fan and ionizer are stopped but kept in standby mode.

• The system monitors the appearance of carbon monoxide (CO) in the room air and, if a harmful gas is detected, automatically turns on the incoming fan at maximum speed, creating overpressure that increases traction, while atmospheric oxygen (02) contributes to complete combustion, and overpressure - to remove flue gases through the chimney.
• The system monitors the humidity in the room and when it exceeds 75%, it automatically turns on the fan and ionizer. They turn off 10 minutes after the indoor humidity is below 75%.

FAN SPEED- Controls the fan speed.

Fan speed selection:

1. first speed - 45 m3 / h in night, silent operation mode
2. second speed, maximum - 70 m3 / h in daytime operation

Air supply mode - the system continuously supplies clean air from outside to inside.

(Used when the fireplace is not working)

Mode (Reverse ventilation with heat recovery).

• The system pumps clean ambient air from outside to inside and throws polluted air from the room to the outside. Heat recovery is provided - the process of returning heat from the outgoing polluted but warm room air.
• Passing through the heat exchanger, warm air released in the room, gives off most of its heat to the clean, but cold air entering the room. This significantly reduces heat loss on cold winter days. In summer, the opposite process is observed - cold air from an air-conditioned room, passing through a heat exchanger, cools the warm and clean air entering the room.
• The heat exchanger / recuperator / achieves a regeneration efficiency of more than 90%.

Eco-Freshness 01 Lux - high-quality supply and exhaust ventilation for home and office

Air handling unit Eco-Freshness 01 Lux MMotors with a heater will provide your home or office with the necessary amount of clean fresh air, while maintaining a comfortable level of humidity and warmth. The built-in recuperator heats or cools the incoming air, if necessary, significantly reducing the load on the air conditioner or heating system. Has a built-in humidity sensor.

Passing through the unit, the air is filtered by a charcoal filter to remove most of the pollutants, such as dust, animal hair, plant pollen, carbon monoxide, exhaust gases, microorganisms.

The device is equipped with ionizer which will fill space with negatively charged ions. They have a beneficial effect on human health and well-being and help to overcome those viruses and bacteria that are already in the room.

The Eco-Freshness 01 Lux supply and exhaust ventilation unit is indispensable for people with allergies, respiratory diseases, as well as those who are especially demanding on the quality of the air they breathe.

Why is it important to breathe fresh air?
Very often, increased fatigue, drowsiness and reduced immunity are associated with the poor quality of the air we breathe. Plastic sealed windows at home and in the office, lack of proper ventilation and stagnant air - and now we no longer feel vigorous, it is difficult for us to concentrate on anything, and by the evening there is no energy left at all.

Airing through windows has a number of significant disadvantages:

• Along with the air, dust, allergens, exhaust gases enter the room
• If the windows overlook a noisy street, then you will be constantly distracted by otherworldly sounds.
• In summer, the coolness quickly disappears through the windows, and in winter it is warm. This increases the energy consumption for heating or cooling.
• Drafts appear that can harm your health
• It is impossible to accurately control the volume of air
• With window ventilation, the humidity level in the room increases greatly, and in dry conditions, on the contrary, it decreases.

All these problems disappear when using the Eco-Freshness 01 Lux air handling unit!

How is the Eco-Freshness 01 Lux MMotors installation arranged?

System management

All settings can be easily entered using the remote control remote control which is included in the package. The following functions are provided:

• Turning the system on / off
• Mode control: reversible ventilation, supply ventilation mode, night mode
• Choice of performance (5 speeds)
• Setting to automatically turn on when the humidity level rises
• Switching on the ionizer
• Turning on the heater

Advantages and features of Eco-Freshness 01 Lux MMotors:

• High work efficiency
• Purification of the supplied air from allergens
• Ceramic heater
• Ionizer
• Charcoal filter
• Keeping warm or cool indoors
• Humidity sensor
• CO 2 sensor
• Minimum wall thickness - 270 mm
• Ф holes - 105 mm
• No condensation
• A safety valve blocks air movement when the device is turned off
• Night silent mode (35 m3 / h)
• Simple assembly
• Built-in thermostat
• Outside operating temperature range -25 ... + 40 degrees
• Internal operating temperature range 0 ... + 50 degrees
• Remote control included
• 5 fan speeds
• Reverse ventilation mode with recuperation
• Supply ventilation mode
• Mode exhaust ventilation
• Sleep mode (stop working in the dark)
• Automatic switching on when the humidity level rises to 75%
• Protection class IP X4
• For rooms up to 28 m2
• Country of origin - Bulgaria

You can buy the Eco-freshness 01 Lux air handling unit in St. Petersburg at a bargain price in our online store. We also carry out installation of the Eco-freshness ventilation unit MMotors.

The most innovative recuperative devices are air handling units. Compact air handling units are necessary for cleaning, supplying and removing used air in small rooms and buildings. Humidification and heating of the air mass is carried out by means of a plate recuperator made in the form of a membrane. This membrane transfers heat from the used air to the outside air. The equipment is installed in a room with a false ceiling.

Compact air handling units

Standard equipment consists of exhaust and supply fans, extract and supply filters, plate membrane, automatic control system, remote control. A high-tech recuperator humidifies and warms up the air. Moreover, the membrane transfers only molecules of heated water, and all impurities remain in the exhaust air. Compact air handling units are equipped with fans with specially designed impellers and asynchronous motors. Motor bearings are sealed for durability and maintenance-free. The motors of the unit are equipped with a protection system. Built-in thermal contacts automatically restart the motor at a temperature of 125 degrees. Compact air handling units are equipped with motors with two speed modes. External electric heater control unit is supplied separately. Additionally, an electronic frost protection of the membrane is provided. If the air duct network is too ramified, then it is possible to install additional back-pressure fans (separate delivery).

Compact air handling units are essentially a ready-made supply ventilation system that supplies residential and public buildings with fresh air. Structurally, all elements of the unit are placed in one housing with thermal and sound insulation, therefore they are practically silent, small-sized and fairly easy to install. V winter period the compact unit is designed to heat the supply air. An air heater is used for this purpose. Structurally, they are either electric or water-based. The water-type heater is connected to central or autonomous heating, which significantly save energy. Such heaters are usually used when heating cottages, summer cottages and country houses.

A series of supply units and supply and exhaust units "EKO-Freshness"

Ventilation unit "EKO-Freshness" providesno ventilation separate premises, improves air quality and maintains a relative humidity of no more than 70%.

Operating conditions of the EKO-Freshness installation:

The EKO-Freshness unit should be operated in indoor, closed and dry rooms with a temperature environment from 0 ° С to + 50 ° С.
The transported air must have a temperature ranging from -25 ° C to + 40 ° C and a relative humidity of up to 90%.

Description:

The air processed by the "EKO-Freshness" unit will breathe through a 2-stage filtration, heated by an electric heater (in the cold season) and ionized (optional). Thus, the unit supplies fresh air, free from dust and odors, at room temperature.

Mounting:

Wall thickness from 400 to 700 mm, bore Ø 152 mm. (for "EKO-Freshness" 01 - Ø135).

EKO-Freshness installation complete set:

:

1. Outer grill - prevents rain drops and due to the installed mesh - various objects.
2. Carbon Filter - purifies the air even in polluted urban and industrial areas. Cleans from odors, dust, soot,car exhaust, etc.
3. Fine filter - additional cleaning from dust, dust and other small particles.
4. Valve - prevents drafts when the unit is shut down.
5. Stopper (fig. 2) - fixes the installation length depending on the wall thickness.
6. Fan - provides air flow from 30 m3 / h in silent night mode to 120 m3 / h in day mode.
7. Heater 2x300W - maintains the temperature of the air entering the room within 25 ° C. The supply unit "EKO-Freshness" contains 2 heaters, a catThey guarantee Δt = 15 ° С (the difference between the temperature of the outside air and the air entering the room), when the unit is operating at a maximum capacity of 120 m3 / h.

ATTENTION!
When the outside temperature is below -10 ° C, it is necessary to reduce the turnovers of the fan in order to guarantee the temperature of the air entering the room at + 25 ° C.

8. Thermostat - controls the heater, thus maintaining the temperature supply air at + 25 ° C.
9. Ionizer - cleans, disinfects and refreshes the air. Eliminates unpleasant odors. Destroys microorganisms. Protects against mold.
10. Decorative grille - can be white, gray, black or metallized.
11. Control panel - speed controller, switches, humidity sensor and timer.
The humidity sensor turns on the unit fan at 100% capacity if the humidity level in the room exceeds 70%.
The timer ensures the operation of the unit at 100% capacity within 5 minutes after turning on the system and after the moisture level has dropped below 70%.
11.1. Regulator - for smooth regulationfan speed control from 900 / min to 2650 / min and air flow change from 30m3 / h to 120m3 / h.
11.2. Switches:

Plant with heat recovery, humidity sensor and capacity up to 100m 3 / h

The device can be tested in our address Bolshaya Tulskaya house 10, building 3

Description of the Eco-Freshness 01 Standard unit

Air handling unit Eco-Fresh 01 Standardwith heat recuperator has a capacity of 30-100 m³ / h, charcoal filter, humidity sensor. It is possible both to work on the inflow and exhaust, and only on the inflow. There are two speeds available. The minimum wall thickness is 270 mm. The device is suitable for both country houses and city apartments.

Installation characteristics

• Removes exhaust air from the room and replaces it with fresh outside air.
• Can only work on inflow.
• Cleans incoming air from dust, harmful impurities, exhaust gases and unpleasant odors.
• Monitors and regulates humidity levels indoors, prevents the formation of mold and mildew.
• The compact dimensions of the unit allow it to be mounted inside a room wall.

Equipment

The Eco-Freshness 01 Standard air handling unit includes:

1.External protective grille (square white)- protects the system from moisture, even in heavy rain.

2. Telescopic air duct- allows you to adjust the length of the device in accordance with the thickness of the wall.

3. Exhaust fan - two-speed, allowing to adjust the volume of the outgoing air flow from 30 m 3 / h to 100 m 3 / h.

4. Filter with activated carbon - guarantees the flow of fresh air even in heavily polluted urban and industrial areas. Cleans the air from odors, dust, bacteria, soot, exhaust gases from cars, etc.

5. Recuperator(heat exchanger) - contributes to a significant reduction in temperature losses during ventilation of premises.

6. Ionizer(only in Lux configuration) - saturates the air with negative ions. Removes specific and unpleasant odors. Destroys pathogens. Prevents the formation of mildew and mildew.

7. Supply fan- two-speed, allowing you to adjust the volume of incoming air from 30 m 3 / h up to 100 m 3 / h Used to blow clean air from outside to inside.

8. Decorative grille- does not take up space in the room, it can be painted in different colors.

9. Humidity sensor- turns on ventilation when the humidity exceeds 75%.

10. CO carbon monoxide sensor (only in the complete set Comfort)- turns on the supply fan in the Air Flow mode -> 100 m 3 / h, when the CO level is higher than the allowable one.

Instrument control

The control is carried out via a wall-mounted control panel. The following operating modes are provided:

1. Reverse ventilation with heat recovery... The system pumps clean fresh air into the room and throws polluted air outside the room.

2.Continuous inflow mode air

The fan speed can be set: 30 m 3 / h or 100 m 3 / h.

About the manufacturer

MMotors is a Bulgarian manufacturer of climatic equipment, specializing in the production of ventilation systems. The company MMotors was founded in 1961.

MMotors company specializes in the production of ventilation units for both industrial scale and residential premises.

MMotors is an excellent, well-established production of high-quality equipment that meets all the specified European standards.

At the production workshops of MMotors, only proven and high-quality materials that have passed a thorough check are used, and only high-tech and modern equipment is used.

If we talk about the advantages of the company MMotors, then the first thing to start with is to indicate the correspondence of price and quality, since for a relatively low price the company MMotors offers high-quality equipment that meets all the needs of a modern person.

Eco-Freshness 01 Standard supply and exhaust system, with a heat recuperator. 30 - 100 m³ / h, 18 W (fan), carbon filter. Regulator of modes and speed (2 steps), wall-mounted.

Standard installation cost :

• standard installation - check with the manager.

Forced automatic inclusion when the permissible level of carbon monoxide is exceeded. Minimum wall thickness 270 mm, Ø 105 mm.

Compact air handling unit Eco-freshness 01 is intended for ventilation of individual rooms, residential and administrative buildings, children's health care facilities, etc.

Creates a healthy microclimate, which is especially important for people with asthma and allergies. Prevents the appearance of mold and mildew.

Normalizes humidity in the room due to the inflow of fresh filtered air.

If necessary heats up the air.

Wired remote

Low power consumption

Compact dimensions

Fits easily into thick walls

Carbon filter removes burning and exhaust odors

CO sensor

Speed ​​controller (2 steps)

Humidity sensor

Silent electric motor on radial ball bearings of a closed type, which guarantees many years of trouble-free operation of the system

Built-in spring check valve protects the room from street noise and outside air when the system is turned off
It is also recommended to use it in rooms where a fireplace is installed. In most cases, such systems are unprofessional designed and do not anticipate the supply of fresh air to the room. Despite popular belief, periodic opening of doors and windows is not an effective solution to the problem.
When the fresh air entering the room is insufficient, the result is a lack of oxygen and incomplete combustion, and carbon monoxide CO, a highly toxic, odorless and colorless gas, is formed into the room. CO is a threat to our lives and health and is the cause of accidents when heating with solid fuels.

To ensure a healthy microclimate when heating with a fireplace or solid fuel stove, fresh air must be supplied to the room at least 4 m3 / h for each kilowatt of heat output (when heating with a fireplace with an open flame, the need for fresh air is much greater).

Considering the need for overpressure in a room with a fireplace or solid fuel stove, the use of a ventilation system that ensures the flow of clean air is especially important for both good combustion and our health.

The compact ventilation system "ECO-FRESH 01" creates a healthy microclimate, delivering clean, filtered and oxygenated air to the room

The system cleans the air entering the room from odors, dust, bacteria and car exhaust gases.

It is recommended to replace the filter every 6 months. In heavily polluted areas, the filter should be changed more often.
The carbon monoxide detector turns on the system automatically when CO is released in the room (only in the COMFORT model).